10 February 2018

Build the Back to the Future DeLorean - Issues 024-027

Issues 024-027
Still no Issue 020.  Without this elusive issue, we are unable to continue to build off the engine.  Issues 024 to 026 finish off the engine assembly.  While we wait for Issue 020 to arrive, we can look at the issues and parts from this shipment

Issue 024 - Pulleys and Belts

Issue 024 contents
This looks fun, there are pulleys and belts to assemble.  I thought I could build off of that I had since none of these parts directly connect to anything from Issue 020 or 021.  As you may recall, you need 020 to work on 021.

Anyway, the upper parts of the engine assembly need to be assembled in order for the belts to go on.  Sure, I could have just mounted the pulleys.  But, what is the point?

Issue 025 - Heat Shield and Exhaust Pipes

Issue 025 contents
Again, some of these parts can be build on to the existing block.  But, the heat shield and brackets need to be on top of the pulleys and belts...which are not on the block yet because of missing parts.  Argh!

Issue 26 - Exhaust and Mounting Engine

Issue 026 contents
Remember the two inner drive shafts from Issue 014?  Well, this you can finally mount them when you mount the engine on to the frame.  But, that is only if you have all the issues and parts up to this point.  Otherwise, you will need to wait for parts.

Reports of Issues 022, 023, and 024 are also on back order.  I guess the good news is these are all engine parts.  You could just move on to another area of the car...which brings us to...

Issue 027 - Radiator Fans and Horn

Issue 027 contents
Finally, we can build something.  We also get introduced to three new screws!  This issue is quite easy to build.

DeLorean owners/enthusiasts will notice that there is only one horn, on the driver's side.  A DeLorean has two horns, one on each side.  Yep, the DMC-12 has stereo horns.  Actually, one 'high' note, one 'low' note to create that distinctive 'dying duck' sound.  Side note:  One of the items of the bottom of my list is to replace my horns with something that has a little more umph!

The radiator fan build is pretty straight forward.  Just mount the fans onto the frame.  You will have to set these aside until (I guess) you receive the radiator itself.  Then they will mount on the radiator brackets.

Another note.  The fan blades are a little off.  The blades on a DeLorean fan are off set.  More of an 'X' shape than a traditional 'cross' shape.  Here we have four blades that are 90° from each other.  On a DeLorean, the blade are set at about 60° apart.  Think of a six-bladed fan, and remove the top and bottom blade.  Look here is a picture:

Stock cooling fans
These are stock.  Perhaps Doc replaced these goofy off set fans and replaced them with a 'normal' fan design.

Okay, with Issue 027 assembled, it should look like this:

Horn, radiator bracket, and cooling fans assembled
Now, we wait and hope for 020 to ship along with the next issues.

Screw count.  I did not work on Issues 024-026, so there are no 'extra' screws to add to the collection.  As mentioned, there are three new screws introduced in 027, so here is the count, omitting 020, 022, 024, 025, and 026.

24-AP, 7-BP, 2-CP, 8-AM, 6-BM, 4-EM, 4-CM, 8-DM, 2-DP, 1-FM, 3-GM, 3-HM, 2-IM, 1-EP, 2-FP, 1-JM, 1-HP, 1-GP, 1-NM

to be continued...




No comments:

Post a Comment